OldComp.cz

Komunitní diskuzní fórum pro fanoušky historických počítačů


Právě je 19.03.2024, 09:29

Všechny časy jsou v UTC + 1 hodina [ Letní čas ]




Odeslat nové téma Odpovědět na téma  [ Příspěvků: 6 ] 
Autor Zpráva
 Předmět příspěvku: (English) Aritma 0516 dc motor
PříspěvekNapsal: 17.05.2021, 12:42 
Offline
Stydlín

Registrován: 26.08.2019, 12:42
Příspěvky: 7
Bydliště: Greece
Has thanked: 2 times
Been thanked: 0 time
Hi! to all out there...

I came this form in order to gather more infos on my own Aritma 0516 plotter. It was working for years but suddenly I dig it out to run a test on it with my retro computer but I have the following problem:

It initializes ok on moving the head far left.
It plots ok but when I try to park or pick a pen the moving pens holder bar moves forward to change/park pen and is stuck in the engaged position. If i open the printer and rotate the DC motor shaft (located far left) a little bit with my finger the mechanism is working (although very very slow ) to the initial position until next time it is stuck again.

I guess maybe is a problem with DC motor, dc voltage range, reverse problem , driver problem etc , I examined your schematic found from a link here but I cannot find the section refers to this motor.
Any suggestions?

Thank you for your excellent forum infos and your time

Alex
GR

Sorry for my English but I dont know your language ;)

_________________
member of www.retroclub.gr


Nahoru
 Profil  
 
 Předmět příspěvku: Re: (English) Aritma 0516 dc motor
PříspěvekNapsal: 17.05.2021, 13:27 
Offline
Profík

Registrován: 06.03.2018, 16:00
Příspěvky: 946
Bydliště: Valtínov, Kunžak
Has thanked: 38 times
Been thanked: 471 times
Hello, circuit is on sheet 516-20511--4 L.2 (5), in bottom part.

P.


Nahoru
 Profil  
 
 Předmět příspěvku: Re: (English) Aritma 0516 dc motor
PříspěvekNapsal: 17.05.2021, 16:04 
Offline
Stydlín

Registrován: 26.08.2019, 12:42
Příspěvky: 7
Bydliště: Greece
Has thanked: 2 times
Been thanked: 0 time
Thank you my friend.... I will proceed with repair now

_________________
member of www.retroclub.gr


Nahoru
 Profil  
 
 Předmět příspěvku: Re: (English) Aritma 0516 dc motor
PříspěvekNapsal: 17.05.2021, 20:00 
Offline
Óm Nejvyšší
Uživatelský avatar

Registrován: 07.07.2019, 22:14
Příspěvky: 3748
Has thanked: 269 times
Been thanked: 447 times
If you are happy, we are happy :-). It is nice to see Aritma 0516 is still used nowadays even just for fun outside former Czechoslovakia. GR is for Ελληνική Δημοκρατία?


Nahoru
 Profil  
 
 Předmět příspěvku: Re: (English) Aritma 0516 dc motor
PříspěvekNapsal: 18.05.2021, 10:50 
Offline
Stydlín

Registrován: 26.08.2019, 12:42
Příspěvky: 7
Bydliště: Greece
Has thanked: 2 times
Been thanked: 0 time
Yes I used Aritma connected on my (retro) Commodore 64! in a retro event party in my city (as a member of rectroclub.gr)

phpBB [video]

https://www.youtube.com/watch?v=oQPBUttDcHo

_________________
member of www.retroclub.gr


Nahoru
 Profil  
 
 Předmět příspěvku: Re: (English) Aritma 0516 dc motor
PříspěvekNapsal: 20.05.2021, 10:09 
Offline
Stydlín

Registrován: 26.08.2019, 12:42
Příspěvky: 7
Bydliště: Greece
Has thanked: 2 times
Been thanked: 0 time
Well SUCCESS with the repair.

In the following foto you can see the motor that was stuck in one direction/and turned slowly on other direction while pen exchange.

Příloha:
motor.jpg
motor.jpg [ 369.23 KiB | Zobrazeno 6896 krát ]


I measured the voltage across motor pole and I read 5V (??!) weird reading as according to schematic motor should get 28V!

Příloha:
change_driver_sch.jpg
change_driver_sch.jpg [ 128.57 KiB | Zobrazeno 6896 krát ]


So I understand that there should be driver problems so I checked PCB (red circle)

Příloha:
short.jpg
short.jpg [ 585.98 KiB | Zobrazeno 6896 krát ]


I measured BD710 & BD709 and also the 4 diodes but I could not see any problem.

Suddenly I noticed that a resistor long wire was shorting with output of a BD transistor (!?) .Violla! that was the problem:the triger voltage (at the base of BD ) was passing at the output stage directrly providing the output with incorrect 5v instead of the correct 28V (!!!)

_________________
member of www.retroclub.gr


Nahoru
 Profil  
 
Zobrazit příspěvky za předchozí:  Seřadit podle  
Odeslat nové téma Odpovědět na téma  [ Příspěvků: 6 ] 

Všechny časy jsou v UTC + 1 hodina [ Letní čas ]


Kdo je online

Uživatelé procházející toto fórum: Žádní registrovaní uživatelé a 1 návštěvník


Nemůžete zakládat nová témata v tomto fóru
Nemůžete odpovídat v tomto fóru
Nemůžete upravovat své příspěvky v tomto fóru
Nemůžete mazat své příspěvky v tomto fóru
Nemůžete přikládat soubory v tomto fóru

Hledat:
Přejít na:  
Založeno na phpBB® Forum Software © phpBB Group
Český překlad – phpBB.cz